Wireless NVR System

Wireless NVR System

For xmarto wireless system
Inner Question

Inner Question

How to configure xmartO wireless cameras to work wired

Wireless NVR Systemwemark Published the article • 0 comments • 635 views • 2017-09-11 15:39 • 来自相关话题

If your cameras are out of the WiFi range of the NVR, you may need to hard wire your cameras to make them work. Then, please follow the instructions blew to configure your cameras to work wired:
 
1. Right click you NVR mouse, then click Device Manage to enter the interface below. Select the channel that you want to wire in the lower box, and Delete it. Then this channel will switch to "No Video Source"





 
2. Connect the camera to the LAN port at the back of your NVR with a network cable and plug the camera to power. If there is no available LAN port at the back of your NVR, please plug the camera to your router. The router here should be connected to your NVR.
 
3. Go to Device Manage interface, click "Refresh" at upper right corner, wait for a while, you shall see the cameras with IP address 192.168.1.168 appears in the upper box.





 
4. Select an unoccupied channel in the lower box, and double click the camera in the upper box, then the camera will be added to the channel to work wired.










 
Note: If the status of the channel is “Different Net Segment”, that means the camera's IP address is not in the same net segment with your router's IP address. In this case, you need to change your camera's IP address to the same net segment of your router. Please refer to the instruction in the document attached to change your camera's IP address.

After you change the camera's IP address, please start from the step 1 to reconfigure the camera to work wired again.
 
For more help on how to confirgure wireless cameras to work wired, please contact us at support@xmarto.com.
 
 
  查看全部
If your cameras are out of the WiFi range of the NVR, you may need to hard wire your cameras to make them work. Then, please follow the instructions blew to configure your cameras to work wired:
 
1. Right click you NVR mouse, then click Device Manage to enter the interface below. Select the channel that you want to wire in the lower box, and Delete it. Then this channel will switch to "No Video Source"

delete_wireless_camera.jpg

 
2. Connect the camera to the LAN port at the back of your NVR with a network cable and plug the camera to power. If there is no available LAN port at the back of your NVR, please plug the camera to your router. The router here should be connected to your NVR.
 
3. Go to Device Manage interface, click "Refresh" at upper right corner, wait for a while, you shall see the cameras with IP address 192.168.1.168 appears in the upper box.

Refresh.jpg

 
4. Select an unoccupied channel in the lower box, and double click the camera in the upper box, then the camera will be added to the channel to work wired.

add_the_wired_camera_to_the_lower_box.jpg


work_wired.jpg

 
Note: If the status of the channel is “Different Net Segment”, that means the camera's IP address is not in the same net segment with your router's IP address. In this case, you need to change your camera's IP address to the same net segment of your router. Please refer to the instruction in the document attached to change your camera's IP address.

After you change the camera's IP address, please start from the step 1 to reconfigure the camera to work wired again.
 
For more help on how to confirgure wireless cameras to work wired, please contact us at support@xmarto.com.
 
 
 

After I select the NVR system, the life display always give error message "fail to connect", why?

Reply

Inner QuestionPeterHsi7 Post a question • 3 person concerned • 0 replies • 378 views • 2017-09-03 07:42 • 来自相关话题

xmartO ESeeCloud CMS for Mac

Wireless NVR Systemwemark Published the article • 0 comments • 792 views • 2017-07-26 17:57 • 来自相关话题

EseeCloud is an updated CMS to preview, playback and backup the xmartO cameras/ camera systems on Mac.
 

1. Download ESeeCloud CMS Software
Download the EseeCloud CMS from xmartO website:
www.xmarto.com/download/cms/CMS1.2.2.dmg 
 
2. Install and run ESeeCloud CMS on your Mac.
Install the CMS on your Mac and run it. If you have problem installing ESeeCloud CMS to your Mac, please refer to "How to Allow Apps from Anywhere in macOS Sierra Gatekeeper".

3. Login ESeeCloud
After that, you will be asked to type in the username and password. The default username is "admin", default password is blank. For security reason, please set a login password to prevent unauthorized access. 




 
4. Add Device to ESeeCloud CMS

4.1 Auto add, applies to add devices in LAN
EseeCloud CMS will search the devices in LAN automatically and display them in the Device Management list.

a. Click “Device Management” in upper navigation, you’ll see your device(s) listed there.
b. Select the device(s) and click Add. Your device(s) will be added to ESeeCloud CMS. They will show on upper right.








 
c. Go back to Live View, and click on the "play button" 


 behind each device to preview. If you want to view cameras from all devices at the same time, simply click “All Connect” at the right bottom. Click on the "stop button" behind each device to stop previewing cameras of this device.




 

4.2 Manual add, applies to add devices remotely
If you want to view cameras from a remote computer, you need to add the device to your ESeeCloud CMS manually on that computer.

a. Run and login ESeeCloud, then click “+” at top right corner. Or click “Device Management” on upper navigation.




 
b. You’ll see below interface. There are two ways to add device to ESeeCloud: Add cloud ID and Add IP/DDNS.
Add cloud ID: Add device to ESeeCloud with your NVR’s Device/Cloud ID. It is available for local and remote access.
Add IP/DDNS: Add device to ESeeCloud with your NVR’s IP address. It is available for local access only, so if you want remote access your cameras on this computer, choose the first Add cloud ID.




 
c. Type in the information required and click “Add”, the device is added to this ESeeCloud CMS, you can preview the cameras now.




 
Note: If you are adding xmartO VR camera, please turn on the Panorama.
 
5. Live View
5.1 The ESeeCloud CMS allows you to view cameras on your computer both locally and remotely. Please refer to below image for basic introduction of buttons.




 
5.2 It allows you to view up to 64 cameras simultaneously.




 
5.3 It supports all xmartO security camera systems and VR cameras. You can turn on panorama for VR cameras here, and also you can turn on the auto cruise.




 
6. Playback
The ESeeCloud CMS allows you to playback your camera videos. With this CMS, you can playback videos stored in hard drive or microSD card from all over the world. Detailed instruction as below:

a. Click “Playback” on upper navigation.
b. Select a window on left(1), select a channel from the device(2), choose the type(3), and select a date(4), click “Search”(5). The CMS will start playback videos on camera windows shortly. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.




 
Note: The ESeeCloud CMS allows you to playback 4 cameras at the same time.
 

7. Backup (It works in LAN network only)
The ESeeCloud CMS allows you to download and backup videos to your computer.
The recorded video files are in .avi format, you can playback with any player.

Detailed instruction here:
Click “Resource Management” on upper navigation, then select the channel you want to back up, select the type and date, click “Search”, you will see the recordings on the left. Click the “Download” icon to download the videos you want. Videos will be saved to your computer.




 
Videos will be saved to below path in default:
 
/Users/macusername/cms_data/cms_video_download/ 
 
You can change the storage path here:
Click the setting icon at upper right corner, then you’ll see below box. Click the three dots to change the storage path, and click Confirm.




 
 
8. User Management
8.1 Change admin password
The ESeeCloud CMS’s default username is admin, and default password in blank, means no password. For security consideration, we suggest you set a password for CMS after logged in. Here is how:
 
Click the “human” icon at upper right corner, then click Change Password. Keep the old password blank, and enter your new password, confirm your new password, and click Confirm.








 
8.2 Add new user
You can add new user for ESeeCloud CMS, here is how:
Click User Management on upper navigation, then click New, you’ll see below box.
Enter a username and remark name, click Confirm. (Remark name here is your nick name.)






Note: When you create a new user, you are not asked to enter new password for this user. It uses default password blank. You can change the password after logged in.

For more questions about this ESeeCloud CMS, please contact xmartO support at support@xmarto.com  查看全部
EseeCloud is an updated CMS to preview, playback and backup the xmartO cameras/ camera systems on Mac.
 

1. Download ESeeCloud CMS Software
Download the EseeCloud CMS from xmartO website:
www.xmarto.com/download/cms/CMS1.2.2.dmg 
 
2. Install and run ESeeCloud CMS on your Mac.
Install the CMS on your Mac and run it. If you have problem installing ESeeCloud CMS to your Mac, please refer to "How to Allow Apps from Anywhere in macOS Sierra Gatekeeper".

3. Login ESeeCloud
After that, you will be asked to type in the username and password. The default username is "admin", default password is blank. For security reason, please set a login password to prevent unauthorized access. 
1.png

 
4. Add Device to ESeeCloud CMS

4.1 Auto add, applies to add devices in LAN
EseeCloud CMS will search the devices in LAN automatically and display them in the Device Management list.

a. Click “Device Management” in upper navigation, you’ll see your device(s) listed there.
b. Select the device(s) and click Add. Your device(s) will be added to ESeeCloud CMS. They will show on upper right.
add_device.png

device_added.png

 
c. Go back to Live View, and click on the "play button" 
button.png
 behind each device to preview. If you want to view cameras from all devices at the same time, simply click “All Connect” at the right bottom. Click on the "stop button" behind each device to stop previewing cameras of this device.
live_view.png

 

4.2 Manual add, applies to add devices remotely
If you want to view cameras from a remote computer, you need to add the device to your ESeeCloud CMS manually on that computer.

a. Run and login ESeeCloud, then click “+” at top right corner. Or click “Device Management” on upper navigation.
2.png

 
b. You’ll see below interface. There are two ways to add device to ESeeCloud: Add cloud ID and Add IP/DDNS.
Add cloud ID: Add device to ESeeCloud with your NVR’s Device/Cloud ID. It is available for local and remote access.
Add IP/DDNS: Add device to ESeeCloud with your NVR’s IP address. It is available for local access only, so if you want remote access your cameras on this computer, choose the first Add cloud ID.
1.png

 
c. Type in the information required and click “Add”, the device is added to this ESeeCloud CMS, you can preview the cameras now.
2.png

 
Note: If you are adding xmartO VR camera, please turn on the Panorama.
 
5. Live View
5.1 The ESeeCloud CMS allows you to view cameras on your computer both locally and remotely. Please refer to below image for basic introduction of buttons.
3.jpg

 
5.2 It allows you to view up to 64 cameras simultaneously.
64.png

 
5.3 It supports all xmartO security camera systems and VR cameras. You can turn on panorama for VR cameras here, and also you can turn on the auto cruise.
VR_CAM.png

 
6. Playback
The ESeeCloud CMS allows you to playback your camera videos. With this CMS, you can playback videos stored in hard drive or microSD card from all over the world. Detailed instruction as below:

a. Click “Playback” on upper navigation.
b. Select a window on left(1), select a channel from the device(2), choose the type(3), and select a date(4), click “Search”(5). The CMS will start playback videos on camera windows shortly. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.
3.jpg

 
Note: The ESeeCloud CMS allows you to playback 4 cameras at the same time.
 

7. Backup (It works in LAN network only)
The ESeeCloud CMS allows you to download and backup videos to your computer.
The recorded video files are in .avi format, you can playback with any player.

Detailed instruction here:
Click “Resource Management” on upper navigation, then select the channel you want to back up, select the type and date, click “Search”, you will see the recordings on the left. Click the “Download” icon to download the videos you want. Videos will be saved to your computer.
Backup.png

 
Videos will be saved to below path in default:
 
/Users/macusername/cms_data/cms_video_download/ 
 
You can change the storage path here:
Click the setting icon at upper right corner, then you’ll see below box. Click the three dots to change the storage path, and click Confirm.
MAC_USRENAME.png

 
 
8. User Management
8.1 Change admin password
The ESeeCloud CMS’s default username is admin, and default password in blank, means no password. For security consideration, we suggest you set a password for CMS after logged in. Here is how:
 
Click the “human” icon at upper right corner, then click Change Password. Keep the old password blank, and enter your new password, confirm your new password, and click Confirm.
change_password.png

set_password.png

 
8.2 Add new user
You can add new user for ESeeCloud CMS, here is how:
Click User Management on upper navigation, then click New, you’ll see below box.
Enter a username and remark name, click Confirm. (Remark name here is your nick name.)

add_new_user.png


Note: When you create a new user, you are not asked to enter new password for this user. It uses default password blank. You can change the password after logged in.

For more questions about this ESeeCloud CMS, please contact xmartO support at support@xmarto.com 

How to Allow Apps from Anywhere in macOS Sierra Gatekeeper

Wireless NVR Systemwemark Published the article • 0 comments • 494 views • 2017-07-26 17:25 • 来自相关话题

Below applies to Mac version older than OSX 10.12.x:
Sometimes upon opening an app you've just downloaded you might see the following error: XX is damaged and can't be opened. You should move it to the Trash. This is a glitch in OS X's Gatekeeper system. Gatekeeper is designed to protect you from malware but you might see this error if you update software, or attempt to run an app that you've previously downloaded and deleted in the past.





 In fact, the app isn't damaged and there's no need to delete it. The solution is as follows:

1. Open System Preferences and click the Security & Privacy icon.

2. Click the padlock icon at the bottom left to unlock System Preferences, entering your password when prompted, then ensure the General tab is selected at the top of the window.

3. Click the radio button alongside “Anywhere”, beneath the Allow Apps Downloaded From heading. You'll be warned this is insecure but, don't worry, this is only temporary.

4. Right-click the troublesome app, then select Open. Ensure the app runs for the first time.

5. Return to System Preferences, and click the radio button alongside Mac App Store and Identified Developers (or just Mac App Store, if you want total security — but this will mean you’ll need to right-click any apps you manually download in future, and right-click them and select Open).

The app is now authorized by Gatekeeper and will run fine in future.




 
Below applies to Mac version OSX 10.12.x and newer:
 
1. Open the Terminal app from the /Applications/Utilities/ folder




 
2. Enter the following command syntax.sudo spctl --master-disable3. Hit return and authenticate with an admin password if needed. You’ll now be able to open and launch apps from anywhere under macOS Sierra.




 
Returning to Default Gatekeeper Security in macOS Sierra:
You can also reverse this and go back to the default strict Gatekeeper settings of only allowing apps from the Mac App Store and identified developers by issuing the following command string:sudo spctl --master-enableHitting return and re-authenticating will return macOS Gatekeeper back to its strict default state of disallowing random apps from launching
 
 

  查看全部
Below applies to Mac version older than OSX 10.12.x:
Sometimes upon opening an app you've just downloaded you might see the following error: XX is damaged and can't be opened. You should move it to the Trash. This is a glitch in OS X's Gatekeeper system. Gatekeeper is designed to protect you from malware but you might see this error if you update software, or attempt to run an app that you've previously downloaded and deleted in the past.
move_to_trash.png


 In fact, the app isn't damaged and there's no need to delete it. The solution is as follows:

1. Open System Preferences and click the Security & Privacy icon.

2. Click the padlock icon at the bottom left to unlock System Preferences, entering your password when prompted, then ensure the General tab is selected at the top of the window.

3. Click the radio button alongside “Anywhere”, beneath the Allow Apps Downloaded From heading. You'll be warned this is insecure but, don't worry, this is only temporary.

4. Right-click the troublesome app, then select Open. Ensure the app runs for the first time.

5. Return to System Preferences, and click the radio button alongside Mac App Store and Identified Developers (or just Mac App Store, if you want total security — but this will mean you’ll need to right-click any apps you manually download in future, and right-click them and select Open).

The app is now authorized by Gatekeeper and will run fine in future.
disable-gatekeeper-mac-os-x.jpg

 
Below applies to Mac version OSX 10.12.x and newer:
 
1. Open the Terminal app from the /Applications/Utilities/ folder
terminal.png

 
2. Enter the following command syntax.
sudo spctl --master-disable
3. Hit return and authenticate with an admin password if needed. You’ll now be able to open and launch apps from anywhere under macOS Sierra.
3.jpg

 
Returning to Default Gatekeeper Security in macOS Sierra:
You can also reverse this and go back to the default strict Gatekeeper settings of only allowing apps from the Mac App Store and identified developers by issuing the following command string:
sudo spctl --master-enable
Hitting return and re-authenticating will return macOS Gatekeeper back to its strict default state of disallowing random apps from launching
 
 

 

New xmartO ESeeCloud CMS for Windows Computer (Supports VR Cameras)

Wireless NVR Systemwemark Published the article • 0 comments • 3934 views • 2017-07-25 17:33 • 来自相关话题

EseeCloud is an updated CMS to preview, playback and backuo the xmartO caemras/ camera systems on PC.
 
1. Download ESeeCloud CMS Software
Download the EseeCloud PC Client Software from xmartO website:
www.xmarto.com/download/app/Es ... 2.exe  
 
2. Install and run ESeeCloud on your computer
Install the software on your PC and run it. If the interface turns into blank after you open it, please right click your mouse, then click "Run as Administrator" to run it.




 
3. Login ESeeCloud
After that, you will be asked to type in the username and password. The default username is “admin”, default password is blank. For security reason, please set a login password to prevent unauthorized access. 





4. Add Device to ESeeCloud CMS

4.1 Auto add, applies to add devices in LAN
EseeCloud CMS will search the devices in LAN automatically and display them in the Device Management list.

a. Click "Device Management" in upper navigation, you'll see your device(s) listed there.
b. Select the device(s) and click Add. Your device(s) will be added to ESeeCloud CMS. They will show on upper right.









 
c. Go back to Live View, and click on the "play button"


behind each device to preview. If you want to view cameras from all devices at the same time, simply click "All Connect" at the right bottom. Click on the "stop button" behind each device to stop previewing cameras of this device.
 



 
4.2 Manual add, applies to add devices remotely
If you want to view cameras from a remote computer, you need to add the device to your ESeeCloud CMS manually on that computer.

a. Run and login ESeeCloud, then click “+” at top right corner. Or click "Device Management" on upper navigation.





b. You'll see below interface. There are two ways to add device to ESeeCloud: Add cloud ID and Add IP/DDNS.

Add cloud ID: Add device to ESeeCloud with your NVR's Device/Cloud ID. It is available for local and remote access.
Add IP/DDNS: Add device to ESeeCloud with your NVR's IP address. It is available for local access only, so if you want remote access your cameras on this computer, choose the first Add Cloud ID.






c. Type in the information required and click "Add", the device is added to this ESeeCloud CMS, you can preview the cameras now.





Note: If you are adding xmartO VR camera, please turn on the Panorama.
 
5. Live View
5.1 The ESeeCloud CMS allows you to view cameras on your computer both locally and remotely. Please refer to below image for basic introduction of buttons.
 



 
5.2 It allows you to view up to 64 cameras simultaneously.





5.3 It supports all xmartO security camera systems and VR cameras. You can turn on panorama for VR cameras here, and also you can turn on the auto cruise.
 



 
6. Playback
The ESeeCloud CMS allows you to playback your camera videos. With this CMS, you can playback videos stored in hard drive or microSD card from all over the world. Detailed instruction as below:

a. Click "Playback" on upper navigation.
b. Select a window on left(1), select a channel from the device(2), choose the type(3), and select a date(4), click "Search"(5). The CMS will start playback videos on camera windows shortly. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.




 
Note: The ESeeCloud CMS allows you to playback 4 cameras at the same time.
 
7. Backup (It works in LAN network only)
The ESeeCloud CMS allows you to download and backup videos to your computer.
The recorded video files are in .avi format, you can playback with any player.

Detailed instruction here:
Click "Resource Management" on upper navigation, then select the channel you want to back up, select the type and date, click "Search", you will see the recordings on the left. Click the "Download" icon to download the videos you want. Videos will be saved to your computer.
 



 
Videos will be saved to below path in default:
C:\Program Files (x86)\EseeCloud\data\cms_video_download\
 
You can change the storage path here:
Click the setting icon at upper right corner, then you'll see below box. Click the three dots to change the storage path, and click Confirm.
 



 
8. User Management
8.1 Change admin password
The ESeeCloud CMS's default username is admin, and default password in blank, means no password. For security consideration, we suggest you set a password for CMS after logged in. Here is how:
 
Click the "human" icon at upper right corner, then click Change Password. Keep the old password blank, and enter your new password, confirm your new password, and click Confirm.









8.2 Add new user
You can add new user for ESeeCloud CMS, here is how:
Click User Management on upper navigation, then click New, you’ll see below box.
Enter a username and remark name, click Confirm. (Remark name here is your nick name.)





Note: When you create a new user, you are not asked to enter new password for this user. It uses default password blank. You can change the password after logged in.
 
For more questions about this ESeeCloud CMS, please contact xmartO support at support@xmarto.com.
 
  查看全部
EseeCloud is an updated CMS to preview, playback and backuo the xmartO caemras/ camera systems on PC.
 
1. Download ESeeCloud CMS Software
Download the EseeCloud PC Client Software from xmartO website:
www.xmarto.com/download/app/Es ... 2.exe  
 
2. Install and run ESeeCloud on your computer
Install the software on your PC and run it. If the interface turns into blank after you open it, please right click your mouse, then click "Run as Administrator" to run it.
QQ图片20170725170430.png

 
3. Login ESeeCloud
After that, you will be asked to type in the username and password. The default username is “admin”, default password is blank. For security reason, please set a login password to prevent unauthorized access. 
1.png


4. Add Device to ESeeCloud CMS

4.1 Auto add, applies to add devices in LAN
EseeCloud CMS will search the devices in LAN automatically and display them in the Device Management list.

a. Click "Device Management" in upper navigation, you'll see your device(s) listed there.
b. Select the device(s) and click Add. Your device(s) will be added to ESeeCloud CMS. They will show on upper right.
add_device.png


device_added.png

 
c. Go back to Live View, and click on the "play button"
button.png
behind each device to preview. If you want to view cameras from all devices at the same time, simply click "All Connect" at the right bottom. Click on the "stop button" behind each device to stop previewing cameras of this device.
 
preview1.jpg

 
4.2 Manual add, applies to add devices remotely
If you want to view cameras from a remote computer, you need to add the device to your ESeeCloud CMS manually on that computer.

a. Run and login ESeeCloud, then click “+” at top right corner. Or click "Device Management" on upper navigation.
2.png


b. You'll see below interface. There are two ways to add device to ESeeCloud: Add cloud ID and Add IP/DDNS.

Add cloud ID: Add device to ESeeCloud with your NVR's Device/Cloud ID. It is available for local and remote access.
Add IP/DDNS: Add device to ESeeCloud with your NVR's IP address. It is available for local access only, so if you want remote access your cameras on this computer, choose the first Add Cloud ID.
b.png



c. Type in the information required and click "Add", the device is added to this ESeeCloud CMS, you can preview the cameras now.
manual_add.png


Note: If you are adding xmartO VR camera, please turn on the Panorama.
 
5. Live View
5.1 The ESeeCloud CMS allows you to view cameras on your computer both locally and remotely. Please refer to below image for basic introduction of buttons.
 
Preview-intro.jpg

 
5.2 It allows you to view up to 64 cameras simultaneously.
64.png


5.3 It supports all xmartO security camera systems and VR cameras. You can turn on panorama for VR cameras here, and also you can turn on the auto cruise.
 
VR_CAM.png

 
6. Playback
The ESeeCloud CMS allows you to playback your camera videos. With this CMS, you can playback videos stored in hard drive or microSD card from all over the world. Detailed instruction as below:

a. Click "Playback" on upper navigation.
b. Select a window on left(1), select a channel from the device(2), choose the type(3), and select a date(4), click "Search"(5). The CMS will start playback videos on camera windows shortly. Move the cursor on the time bar at bottom to locate an exact time to replay the camera per your needs.
playback2.jpg

 
Note: The ESeeCloud CMS allows you to playback 4 cameras at the same time.
 
7. Backup (It works in LAN network only)
The ESeeCloud CMS allows you to download and backup videos to your computer.
The recorded video files are in .avi format, you can playback with any player.

Detailed instruction here:
Click "Resource Management" on upper navigation, then select the channel you want to back up, select the type and date, click "Search", you will see the recordings on the left. Click the "Download" icon to download the videos you want. Videos will be saved to your computer.
 
Backup.png

 
Videos will be saved to below path in default:
C:\Program Files (x86)\EseeCloud\data\cms_video_download\
 
You can change the storage path here:
Click the setting icon at upper right corner, then you'll see below box. Click the three dots to change the storage path, and click Confirm.
 
video_file_path.png

 
8. User Management
8.1 Change admin password
The ESeeCloud CMS's default username is admin, and default password in blank, means no password. For security consideration, we suggest you set a password for CMS after logged in. Here is how:
 
Click the "human" icon at upper right corner, then click Change Password. Keep the old password blank, and enter your new password, confirm your new password, and click Confirm.
change_password.png

set_password.png


8.2 Add new user
You can add new user for ESeeCloud CMS, here is how:
Click User Management on upper navigation, then click New, you’ll see below box.
Enter a username and remark name, click Confirm. (Remark name here is your nick name.)
add_new_user.png


Note: When you create a new user, you are not asked to enter new password for this user. It uses default password blank. You can change the password after logged in.
 
For more questions about this ESeeCloud CMS, please contact xmartO support at support@xmarto.com.
 
 

How to change your NVR resolution if you do not get display on monitor/TV?

Wireless NVR Systemwemark Published the article • 0 comments • 619 views • 2017-07-11 17:50 • 来自相关话题

1. Connect your NVR to the router to make it online.

2. Download the CMS( EseeCloud )from xmartO website: http://www.xmarto.com/downloads/ and install it in your computer.

3. Run the EseeCloud on your computer, it will search the device in LAN and add device automatically. 

4. After your NVR device is added to EseeCloud, click Device Management in upper navigation. Then you will see the interface below. 






5. After you get the NVR IP address, please enter the NVR's IP address in your IE browser, for example, 10.0.0.6, click go. You'll then see below login interface.






6. Input your NVR login username and login password. If you didn't set that, just click Login.
Then you will get to the interface below:






7. Click settings icon on the left bottom, you will get to the settings below:
 





8. Click General, then go to VGA resolution to select the one that is compatible with your monitor/TV and click save. You will hear a beep from your NVR. Wait for a while for the resolution to be correct.

  查看全部
1. Connect your NVR to the router to make it online.

2. Download the CMS( EseeCloud )from xmartO website: http://www.xmarto.com/downloads/ and install it in your computer.

3. Run the EseeCloud on your computer, it will search the device in LAN and add device automatically. 

4. After your NVR device is added to EseeCloud, click Device Management in upper navigation. Then you will see the interface below. 

ip_address.png


5. After you get the NVR IP address, please enter the NVR's IP address in your IE browser, for example, 10.0.0.6, click go. You'll then see below login interface.

2.jpg


6. Input your NVR login username and login password. If you didn't set that, just click Login.
Then you will get to the interface below:

3.png


7. Click settings icon on the left bottom, you will get to the settings below:
 
4.png


8. Click General, then go to VGA resolution to select the one that is compatible with your monitor/TV and click save. You will hear a beep from your NVR. Wait for a while for the resolution to be correct.

 

Can not get cameras on my phone live in real time.

Reply

Inner Questionseclusion29 Post a question • 2 person concerned • 0 replies • 912 views • 2017-06-22 22:38 • 来自相关话题

There is a very long hesitation in cameras when i try to watch them live

Reply

Wireless NVR Systemseclusion29 Post a question • 1 person concerned • 0 replies • 1127 views • 2017-04-20 01:22 • 来自相关话题

Update

Reply

Inner Questiontliving509 Post a question • 1 person concerned • 0 replies • 1239 views • 2016-10-28 18:04 • 来自相关话题

Username and Password

Inner QuestionZDRGN54 Replyed • 1 person concerned • 3 replies • 1622 views • 2016-07-26 00:31 • 来自相关话题